DFM service
Design for manufacture for small, complicated electronics
We prepare tiny, dense devices for the factory: wearables, handheld medical devices and small sensors, where a dense board, a cell, a radio, seals and several materials must fit in a few cubic centimetres. We check every part for moulding, fix what will not work, and hand you a pack a factory can quote from without a meeting.
Only small devices
What we take on, and what we don't
We do this work for our own products, and we offer it only where that experience counts: minute, dense and complicated designs.
We do
- Wearables: bands, rings, clips, patches and pendants
- Handheld and body-worn medical and wellness devices
- Small sensor nodes and trackers with a radio inside
- Enclosures of roughly 10 to 150 mm with a dense board, a cell, sealing and several materials
We don't
- Large enclosures, panels and cabinets
- Appliances, furniture and sheet-metal boxes
- Simple two-part boxes with no fit, seal or radio constraint
What we check
Every part, before steel is cut
Wall thickness
A thickness map of every moulded part, with the thin and thick spots that will short-shot or sink listed by position.
Draft and pull direction
Draft maps for the chosen pull. Faces with no draft are marked, with a proposal for where the geometry must change.
Undercuts and tooling
Undercut maps, side actions and lifters avoided where a small change removes them, gate and ejector positions off the cosmetic faces.
Fits and tolerances
The few dimensions that matter (pusher travel, bores, seats, snap grooves) called out with values a factory can hold, and a question where it may not.
Sealing
O-ring grooves, adhesive joints, acoustic membranes and gaskets laid out so the water path is closed and can be assembled.
Radio keep-out
Metal, coatings and screws kept clear of the antenna; non-conductive finishes specified where the case is near the radio.
Acoustics and optics
Microphone and speaker ports, sealed bells and drivers, light pipes and optical windows with their ink masks.
Materials and processes
Moulding, two-shot TPE, CNC, MIM, NCVM, anodising and glass printing compared for prototype and for 1k and 10k a year.
Our work
Two devices we prepared for the factory
Both are our own products. Click a picture to enlarge it.
Live 3D view
Inside the band: how nine contacts reach the boards
The metal inserts are moulded into the band's bottom shell, so in a solid model their paths are hidden. Here the shell is see-through: gold is the insert metal, red is the spring or sensor on the board that touches it, and the moving dots trace each path from the skin or wall contact to the board. Drag to turn, scroll to zoom, and pick a path to fly to it.
Live 3D view
Stethopod: from heartbeat to Bluetooth, inside the chest piece
The chest piece of our electronic stethoscope, Design D, with its casing made see-through. Follow one heartbeat in five stages: the diaphragm vibrates with each lub-dub, the microphone captures it, the converter (ADC) turns it into digital samples, the board amplifies it, and the radio sends it out over Bluetooth from the antenna. Each stage lights up in turn, with a graph of the signal at that point. Drag to turn, or pick a stage to jump to it.
What you receive
A factory-ready pack
The same pack we send to our own moulders and machine shops, so a factory can quote, ask its questions in writing and return a drafted STEP for our check.
- A DFM brief (PDF)What we ask the factory, the parts and materials, the critical fits, sealing, radio and sound notes, sections and the questions.
- STEP filesOne STEP per part, the casing assembly, and a reference assembly with the boards, cell and bought parts in place.
- BOM and RFQ sheetOne row per part with material, process, size, mass and the values to hold; yellow columns for the quote; a questions sheet for answers.
- A 3D view in the browserRotate, hide parts, cut across or along and explode the stack, with no CAD licence and no install.
- Sections and check mapsExact cross-sections through every critical feature, and thickness, draft and undercut maps of each shell.
- DrawingsDrawings for the parts that need them: pushers, standoffs, bezels, earpieces, glass and its print outline (DXF).
How it works
From your CAD to a factory quote
- 1
Send your design
STEP or native CAD, the board outline and the parts inside. We sign an NDA first if you need one.
- 2
We review it
Thickness, draft, undercuts, fits, sealing, radio and assembly order, with the changes we recommend.
- 3
We build the pack
Brief, STEP per part, BOM and RFQ sheet, sections, check maps, drawings and the 3D view.
- 4
Factory quotes
The pack goes to your factory or ours. We answer their questions and check their drafted STEP before steel is cut.
Questions
Because that is where our experience is. We design our own wearables and medical devices, where a tenth of a millimetre decides whether a part moulds, seals or fits the board. Large enclosures are better served by a general product-design studio.
Contact
Tell us about your device
Give us its size, what is inside (board, cell, radio, sensors, display), the materials you have in mind and the volumes you expect. We reply within two working days, say whether it is a fit for us, and send an NDA before you share files.
Email: info@slimiot.com
Other services: hardware, firmware, apps and dashboards